How to root Android Phone

What is root ?

Root is the organ of a plant that typically lies below the surface of the soil. =O 
In Linux/ Unix Operating System, there are some action only can be carry out by the administrator. The administrator can be so call as root because it has the large access on the system. So rooting can be explain as the process to let the android user  to gain the privileged control on the android system.

With root access, you can

  1. Access More apps
  2. Install Custom Rom's
  3. Access Block Features
  4. Faster Performance
  5. Free Wifi Tethering

However, if you root your devices guarantee will void. So Think twice before your root. Below is the method to root the android phone. Actually there are very easy to root your devices with the help of software. The software I use is the IRoot or last time known as Vroot. 

Click the link to download IRoot : http://pan.baidu.com/s/1dDpgqy9

How to root android phone ?

  1. Install the IRoot
  2. Run Iroot =|
  3. Connect your Phone via USB cable. (Remember open your phone "USB debugging mode".)
  4. Click Connect
  5. Then Click Root to root your devices.
That is How I root my phone. Ok this is the official website of IRoot http://www.mgyun.com/en/getvroot. There are plenty more of the software could help in root your Android. You can share if you found any others software or method to root your devices . Thank you =D



Comments

Post a Comment

Popular posts from this blog

Reading and Writing Operation of SRAM

Image
The diagram below is illustrate Static Random Access Memory (SRAM)Cell for the explanation. SRAM cell is make up of 2 inverters are cross-connected to form a latch .The latch is connected to 2 bit line by transistor T1 and T2 . T1 and T2 can switch opened or closed under control of word line.When word line is ground level, the transistors are turned off and the latch retrains its state. During the Read Operation ,Word line is activated to close switches T1 and T2 . If the cell is in state 1; the signal on b line is high and the signal on b’ line is low.The opposite is true if the cell is in state 0.Thus, b and b’ are always complements of each other’s. The sense /write circuit at the end of the two bit line monitors their state and sets the corresponding output accordingly. While in Write Operation ,the Sense/Write circuit drives bit lines b and b’, instead of sensing their state.It places the appropriate value on bit line b and its complement on b’ and activate the word ...
Read more

Reading & Writing Operation of DRAM

Image
In Dynamic Random Access Memory CELL , transistor acts as a switch to Close (allowing current to flow) when voltage applied in address line or Open (no current flow) when no voltage applied in address line.Address Line also known as word line .Which use to signal the transistor to close or open. During the Write operation ,a voltage is applied on the bit line and a signal applied to the address line to close the transistor.Then the voltage applied on the bit line will transfer to capacitor and store in the capacitor However the capacitor has tendency to discharge and has to refresh to maintain the bit. While in Reading Operation ,the instruction find the bit store using the address line to read the data or bit. When the address line is selected ,the transistor turns on and the charge stored on the capacitor is fled out onto a bit line and to sense amplifier. Sense amplifiers compare the capacitor voltage to reference value to determine the logic 1 or logic 0.The read out from ...
Read more

Method to Convert from Stream to Json C#

Recently I was using the C# HttpClient to make REST request but I found that is was quite troublesome so I have changed to using HttpWebRequest instead. So want the HttpWebRequest result is return it was in Stream form. I not able to convert it into Json. this is the method i convert the stream to JSON. HttpWebResponse response = ( HttpWebResponse ) requirejs . GetResponse (); Stream stream = response . GetResponseStream (); StreamReader sr = new StreamReader ( stream ); var serializer = new System . Web . Script . Serialization . JavaScriptSerializer (); var jsonObject = serializer . DeserializeObject ( sr . ReadToEnd ()); As you can see that jsonObject is an object. Now you can parse it into the Json(JsonObject); If you have any question can leave a comment below.
Read more