Overclocking Non-K intel Skylake CPUs i3 6320

The news that the overclocker called DHENJHEN discovered that Intel core I3-6320 could be overclock using H170 main board about 5Ghz. He found that overclocking limit was only caused by the BIOS itself. There was no special hardmod needed to overclock the core I3 6320 with base clock of 3.9 GHz.


Below is the information for the Skylake architecture.

K- CPUs can be overclocked using the multiplier , non-k CPUs have to be overclocked using the BLCK. 

You can see the information at the http://hwbot.org/submission/3055320_.



Comments

  1. zahwahrachwalMarch 3, 2022 at 6:17 AM

    Casinos & Sportsbook Apps Near DC - JTM Hub
    You'll be 동해 출장안마 the first to know 익산 출장마사지 that gaming is 김제 출장샵 on your way to casinos in 오래된 토토 사이트 the state of Washington. 경상북도 출장마사지 While casinos in the D.C. can be

    ReplyDelete

Post a Comment

Popular posts from this blog

Reading and Writing Operation of SRAM

Image
The diagram below is illustrate Static Random Access Memory (SRAM)Cell for the explanation. SRAM cell is make up of 2 inverters are cross-connected to form a latch .The latch is connected to 2 bit line by transistor T1 and T2 . T1 and T2 can switch opened or closed under control of word line.When word line is ground level, the transistors are turned off and the latch retrains its state. During the Read Operation ,Word line is activated to close switches T1 and T2 . If the cell is in state 1; the signal on b line is high and the signal on b’ line is low.The opposite is true if the cell is in state 0.Thus, b and b’ are always complements of each other’s. The sense /write circuit at the end of the two bit line monitors their state and sets the corresponding output accordingly. While in Write Operation ,the Sense/Write circuit drives bit lines b and b’, instead of sensing their state.It places the appropriate value on bit line b and its complement on b’ and activate the word ...
Read more

Reading & Writing Operation of DRAM

Image
In Dynamic Random Access Memory CELL , transistor acts as a switch to Close (allowing current to flow) when voltage applied in address line or Open (no current flow) when no voltage applied in address line.Address Line also known as word line .Which use to signal the transistor to close or open. During the Write operation ,a voltage is applied on the bit line and a signal applied to the address line to close the transistor.Then the voltage applied on the bit line will transfer to capacitor and store in the capacitor However the capacitor has tendency to discharge and has to refresh to maintain the bit. While in Reading Operation ,the instruction find the bit store using the address line to read the data or bit. When the address line is selected ,the transistor turns on and the charge stored on the capacitor is fled out onto a bit line and to sense amplifier. Sense amplifiers compare the capacitor voltage to reference value to determine the logic 1 or logic 0.The read out from ...
Read more

Method to Convert from Stream to Json C#

Recently I was using the C# HttpClient to make REST request but I found that is was quite troublesome so I have changed to using HttpWebRequest instead. So want the HttpWebRequest result is return it was in Stream form. I not able to convert it into Json. this is the method i convert the stream to JSON. HttpWebResponse response = ( HttpWebResponse ) requirejs . GetResponse (); Stream stream = response . GetResponseStream (); StreamReader sr = new StreamReader ( stream ); var serializer = new System . Web . Script . Serialization . JavaScriptSerializer (); var jsonObject = serializer . DeserializeObject ( sr . ReadToEnd ()); As you can see that jsonObject is an object. Now you can parse it into the Json(JsonObject); If you have any question can leave a comment below.
Read more