3 basic way to speed up computer

Computer is slow?There are many reason can cause the performance of computer become slow.You need to spend some of your time to fixed the problem.You can try the following method to speed up your computer.

The first method is using the Disk Cleanup to speeding up your computer.Disk cleanup is a tool provide by Microsoft that help you to clean up your hard drive.The main problem that cause the computer slow is low hard drive space.So if you clean up your hard drive it may solve your problem.


What you need to do now is start disk cleanup using the following step
  • Click Start, and then click Run. In the Open box, type cleanmgr, and then click OK.

    -or-
  • Click Start, point to All Programs, point to Accessories, point to System Tools, and then click Disk Cleanup.

    -or-
  • In Windows Explorer or My Computer, right-click the disk in which you want to free up space, click Properties, click the General tab, and then click Disk Cleanup.

 The second way to speed up your computer by using the "add and remove programs" .This is the place you can manually add or removing your programs.From here you can view the programs that you are rarely use.You can choose those program and uninstall the programs.This method also can free up lots of hard drive space and enhance your computer performance.

  • To open Add or Remove Programs, click Start, click Control Panel, and then click Add or Remove Programs.
The third method is using the Disk Defragmenter .Disk defragmenter is a system tool of Microsoft window.It function is to rearrange the file inside the hard drive so that the speed of  reading and writing the file can be increase then speed up the computer.

Here is the way to open disk defragmenter:
Start then click run and typein (Dfrg.msc).Click the volume that you want to defragment, and then click Defragment.

Comments

Post a Comment

Popular posts from this blog

Reading and Writing Operation of SRAM

Image
The diagram below is illustrate Static Random Access Memory (SRAM)Cell for the explanation. SRAM cell is make up of 2 inverters are cross-connected to form a latch .The latch is connected to 2 bit line by transistor T1 and T2 . T1 and T2 can switch opened or closed under control of word line.When word line is ground level, the transistors are turned off and the latch retrains its state. During the Read Operation ,Word line is activated to close switches T1 and T2 . If the cell is in state 1; the signal on b line is high and the signal on b’ line is low.The opposite is true if the cell is in state 0.Thus, b and b’ are always complements of each other’s. The sense /write circuit at the end of the two bit line monitors their state and sets the corresponding output accordingly. While in Write Operation ,the Sense/Write circuit drives bit lines b and b’, instead of sensing their state.It places the appropriate value on bit line b and its complement on b’ and activate the word ...
Read more

Reading & Writing Operation of DRAM

Image
In Dynamic Random Access Memory CELL , transistor acts as a switch to Close (allowing current to flow) when voltage applied in address line or Open (no current flow) when no voltage applied in address line.Address Line also known as word line .Which use to signal the transistor to close or open. During the Write operation ,a voltage is applied on the bit line and a signal applied to the address line to close the transistor.Then the voltage applied on the bit line will transfer to capacitor and store in the capacitor However the capacitor has tendency to discharge and has to refresh to maintain the bit. While in Reading Operation ,the instruction find the bit store using the address line to read the data or bit. When the address line is selected ,the transistor turns on and the charge stored on the capacitor is fled out onto a bit line and to sense amplifier. Sense amplifiers compare the capacitor voltage to reference value to determine the logic 1 or logic 0.The read out from ...
Read more

Method to Convert from Stream to Json C#

Recently I was using the C# HttpClient to make REST request but I found that is was quite troublesome so I have changed to using HttpWebRequest instead. So want the HttpWebRequest result is return it was in Stream form. I not able to convert it into Json. this is the method i convert the stream to JSON. HttpWebResponse response = ( HttpWebResponse ) requirejs . GetResponse (); Stream stream = response . GetResponseStream (); StreamReader sr = new StreamReader ( stream ); var serializer = new System . Web . Script . Serialization . JavaScriptSerializer (); var jsonObject = serializer . DeserializeObject ( sr . ReadToEnd ()); As you can see that jsonObject is an object. Now you can parse it into the Json(JsonObject); If you have any question can leave a comment below.
Read more